This page provides a summary of the products we distribute.
Product-specific data for the systems we offer can be found here.
Refer to our Product Selection Guide or Contact Us for more information.
We look forward to hearing from you.
Click here for a PDF of our complete line card.
We are a Canadian distributor for NOV Fiber Glass Systems.
Fibreglass Solutions offers an array of fibreglass piping products suited to the rigors of many corrosive and demanding applications.
Nil-Cor composite valves are a perfect match to a long lasting, low maintenance fibreglass piping system.
More information can be found on our Nil-Cor Valves page.
FRP Bridge Drain has been providing bridge owners with worry-free drainage for decades. Read more on our FRP Bridge Drain page.
Grace Composites also specializes in made-to-order and custom fibreglass components to suit the needs of any project requirement.
Urecon preinsulated piping systems create turnkey insulated FRP piping systems for use in hot and chilled water systems, both above- and below-ground.
A variety of insulation thicknesses and exterior jacket options can be tailored to suit the needs of your application.
Green Thread HP
Method of Construction | Filament-wound pipe to ASTM D2996, filament-found, compression/contact molded fittings to ASTM D5685, filament-wound/compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Reinforced resin-rich corrosion barrier, 20 mil (0.020″) |
Joining Method | Matched tapered bell x spigot joint |
Diameter Range | 1″ – 42″ |
Pressure Rating | 16 – 30 bar (232 – 435 psig) for standard “HP16” design depending on pipe size
Also available in “HP20” 20 bar (290 psig), “HP32” 32 bar (464 psig) and “HP40” 40 bar (580 psig) design ratings |
Temperature Rating | 93°C (200°F), up to 110°C (230°F) by derating pressure |
Green Thread Specification Guide | |
Tapered Bell x Spigot Install Handbook | |
Green Thread HP16 Product Data | |
HP16 Epoxy Fittings Guide | |
HP20 Product Data | |
HP25 Product Data | |
HP20/25 Epoxy Fittings Guide | |
HP32 Product Data | |
HP40 Product Data | |
HP32/HP40 Epoxy Fittings Guide |
Red Thread HP
Method of Construction | Filament-wound pipe to ASTM D2996, filament-found, compression/contact molded fittings to ASTM D5685, filament-wound/compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Not applicable |
Joining Method | Threaded and bonded (T.A.B.) joint (2-6″), matched tapered bell x spigot joint |
Diameter Range | 2″ – 42″ |
Pressure Rating | 16 – 30 bar (232 – 435 psig) for standard “HP16” design depending on pipe size
Also available in “HP25” 25 bar (290 psig) design rating |
Temperature Rating | 93°C (200°F), up to 99°C (210°F) by derating pressure |
Red Thread HP16 Specification Guide | |
Red Thread HP16 Product Data | |
HP16 Epoxy Fittings Guide | |
Matched Tapered Bell x Spigot Install Handbook | |
HP25 Product Data | |
HP25 Epoxy Fittings Guide |
Red Thread HP FM
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound, compression/contact molded fittings to ASTM D5685, filament-wound/compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Not applicable |
Joining Method | Matched tapered bell x spigot joint |
Diameter Range | 4″ – 24″ |
Pressure Rating | 13.8 bar (200 psig) |
Temperature Rating | 93°C (200°F) |
Literature: | Red Thread HP FM Product Data |
Matched Tapered Bell x Spigot Install Handbook |
Centricast CL-2030
Method of Construction | Centrifugally-casted pipe to ASTM D2997, compression/contact molded fittings to ASTM D5685, compression molded flanges to ASTM D4024 |
Resin | Vinyl ester |
Internal Corrosion Barrier | Integral pure resin corrosion barrier, 100 mil (0.100″) |
Joining Method | Adhesive bonded straight socket joint |
Diameter Range | 1″ – 14″ |
Pressure Rating | 5 – 20 bar (75 – 300 psig) depending on pipe size |
Temperature Rating | 93°C (200°F) |
Centricast CL-2030 Specification Guide | |
Centricast CL-2030 Product Data | |
Centricast Fittings Guide | |
Centricast Straight Socket Install Handbook |
Centricast RB-2530
Method of Construction | Centrifugally-casted pipe to ASTM D2997, compression/contact molded fittings to ASTM D5685, compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Integral pure resin corrosion barrier, 100 mil (0.100″) |
Joining Method | Adhesive bonded straight socket joint |
Diameter Range | 1″ – 14″ |
Pressure Rating | 5 – 20 bar (75 – 300 psig) depending on pipe size |
Temperature Rating | 93°C (200°F), up to 121°C (250°F) by derating pressure |
Centricast RB-2530 Specification Guide | |
Centricast RB-2530 Product Data | |
Centricast Fittings Guide | |
Centricast Straight Socket Install Handbook |
Centricast Z-Core
Method of Construction | Centrifugally-casted pipe to ASTM D2997, compression/contact molded fittings to ASTM D5685, compression molded flanges to ASTM D4024 |
Resin | Proprietary thermosetting epoxy |
Internal Corrosion Barrier | Integral pure resin corrosion barrier, 100 mil (0.100″) |
Joining Method | Adhesive bonded straight socket joint |
Diameter Range | 1″ – 8″, larger diameters available on request |
Pressure Rating | 6.9 – 19 bar (100 – 275 psig) depending on pipe size |
Temperature Rating | 135°C (275°F) |
![]() |
Centricast Z-Core Specification Guide |
Centricast Z-Core Product Data | |
Centricast Fittings Guide | |
Centricast Straight Socket Install Handbook |
Silver Streak
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound, compression/contact molded fittings to ASTM D5685, filament-wound/compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Proprietary abrasion-resistant corrosion barrier, 80 mil (0.080″) |
Joining Method | Matched tapered bell x spigot joint |
Diameter Range | 2″ – 24″ |
Pressure Rating | 15.5 bar (225 psig) |
Temperature Rating | 107°C (225°F) |
Silver Streak Specification Guide | |
Silver Streak Product Data | |
Silver Streak Fittings | |
Matched Tapered Bell x Spigot Install Handbook |
Silver Streak Large Diameter (LD)
Method of Construction | Filament-wound pipe to ASTM D2996, contact molded fittings to ASTM D5685, filament-wound/contact molded flanges to ASTM 4024 |
Resin | Vinyl ester |
Internal Corrosion Barrier | Proprietary abrasion-resistant corrosion barrier, 100 mil (0.100″), custom thicknesses available on request |
Joining Method | Flanged joint, butt & wrap joint |
Diameter Range | 30″ – 54″ |
Pressure Rating | 10.3 bar (150 psig) |
Temperature Rating | 93°C (200°F) |
Silver Streak Specification Guide | |
Silver Streak Large Diameter Product Data | |
Silver Streak Large Diameter Fittings | |
Butt & Wrap Install Handbook |
F-CHEM
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound/contact molded fittings to ASTM D5685, filament-wound/contact molded flanges to ASTM D4024 |
Resin | Vinyl ester, resin selection is application dependent |
Internal Corrosion Barrier | Custom design based on application |
Joining Method | Flanged joint, butt & wrap joint |
Diameter Range | 14″ – 72″ |
Pressure Rating | Custom design based on application |
Temperature Rating | 79°C (175°F) typical |
![]() |
F-Chem Specification Guide |
F-Chem Product Bulletin | |
Butt & Wrap Install Handbook |
Ceram Core
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound, compression/contact molded fittings to ASTM D5685, compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | High alumina ceramic and epoxy matrix, 130 mil (0.130″) |
Joining Method | Flanged joint |
Diameter Range | 6″ – 16″ |
Pressure Rating | 6.9 – 15.5 bar (100 – 225 psig) depending on pipe size |
Temperature Rating | 93°C (200°F) |
![]() |
Ceram Core Specification Guide |
Ceram Core Product Data | |
Ceram Core Installation Instructions |
Bondstrand 2400
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound fittings to ASTM D5685, filament-wound flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Reinforced resin-rich corrosion barrier, 30 mil (0.030″) |
Joining Method | Tapered female x male (bell x spigot) joint |
Diameter Range | 2″ – 40″ |
Pressure Rating | 16 – 50 bar (232 – 725 psig) depending on pipe size |
Temperature Rating | 93°C (200°F), up to 121°C (250°F) by derating pressure |
Literature: | Bondstrand 2400 Product Data |
Bondstrand 2400 10-25 Bar Fittings | |
Bondstrand 2400 32-50 Bar Fittings | |
Bondstrand Tapered Joint Assembly Instructions | |
Bondstrand Flange Assembly Installation Instructions | |
Bondstrand Saddle Assembly Instructions |
Bondstrand 2000M
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound fittings to ASTM D5685, filament-wound flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Reinforced resin-rich corrosion barrier, 30 mil (0.030″) |
Joining Method | Quick-Lock straight/taper adhesive bonded socket joint up to 6″, tapered female x male (bell x spigot) joint 8″ – 40″ |
Diameter Range | 2″ – 40″ |
Pressure Rating | 17.2 bar (250 psig) up to 16″, up to 16 bar (232 psig) for 18″ – 40″ depending on fittings |
Temperature Rating | 93°C (200°F), higher operating temperatures available by derating pressure |
Bondstrand 2000M Product Data & Fittings Guide | |
Bondstrand 2000M Flanges | |
Bondstrand Quick-Lock Joint Assembly Instructions | |
Bondstrand Tapered Joint Assembly Instructions | |
Bondstrand Flange Assembly Installation Instructions | |
Bondstrand Saddle Assembly Instructions |
Bondstrand 4000
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound fittings to ASTM D5685, filament-wound flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Reinforced resin-rich corrosion barrier, 50 mil (0.050″) |
Joining Method | Quick-Lock straight/taper adhesive bonded socket joint |
Diameter Range | 2″ – 16″ |
Pressure Rating | 10.3 – 20 bar (150 – 300 psig) depending on pipe size |
Temperature Rating | 93°C (200°F), up to 121°C (250°F) by derating pressure |
Bondstrand 4000 Specification Guide | |
Bondstrand 4000 Product Data | |
Bondstrand 4000 Fittings | |
Bondstrand Quick-Lock Joint Assembly Instructions | |
Bondstrand Flange Assembly Installation Instructions | |
Bondstrand Saddle Assembly Instructions |
Bondstrand 7000M
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound fittings to ASTM D5685, filament-wound flanges to ASTM D4024. Carbon fiber filaments added to all materials for electrical conductivity and grounding of piping system |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Not applicable |
Joining Method | Quick-Lock straight/taper adhesive bonded socket joint up to 6″, tapered female x male (bell x spigot) joint 8″ – 40″ |
Diameter Range | 2″ – 40″ |
Pressure Rating | 17.2 bar (250 psig) up to 16″, up to 16 bar (232 psig) for 18″ – 40″ depending on fittings |
Temperature Rating | 93°C (200°F), higher operating temperatures available by derating pressure |
Literature: | Bondstrand 7000M Product Data & Fittings Guide |
Bondstrand 7000M Flanges | |
Bondstrand Quick-Lock Joint Assembly Instructions | |
Bondstrand Tapered Joint Assembly Instructions | |
Bondstrand Flange Assembly Installation Instructions | |
Bondstrand Saddle Assembly Instructions |
Bondstrand 3000A/3200A
Method of Construction | Filament-wound pipe to ASTM D2996, filament-wound, compression/contact molded fittings to ASTM D5685, filament-wound/compression molded flanges to ASTM D4024 |
Resin | Thermosetting aromatic amine cured epoxy |
Internal Corrosion Barrier | Reinforced resin-rich corrosion barrier 3000A 2″ – 6″, 5 mil (0.005″) 3200A 8″ – 16″, 25 mil (0.025″) |
Joining Method | Tapered female x male (bell x spigot) joint |
Diameter Range | 2″ – 16″ |
Pressure Rating | Up to 31 bar (450 psig) depending on pipe size |
Temperature Rating | 99°C (210°F) |
Literature: | Bondstrand 3000A Product Data & Specification Guide |
Bondstrand 3200A Product Data & Specification Guide | |
Bondstrand 3000 Series Fittings | |
Bondstrand 3000 Series Installation Instructions |
Bondstrand Marine & Offshore Specialty & Fire Resistant Products
Please contact us to discuss your application.
Bridge Drain Piping
Method of Construction | Filament-wound pipe, filament-wound/contact molded fittings and flanges |
Resin | Vinyl ester |
Internal Corrosion Barrier | 10 mil (0.010″) up to 16″, 40 mil (0.040″) 18″ – 24″ |
Joining Method | Adhesive bonded socket joint |
Diameter Range | 4″ – 24″, larger sizes available upon request |
Pressure Rating | Atmospheric gravity drain, typical |
Temperature Rating | Ambient temperatures, typical |
Bridge Drain Pipe Brochure | |
Bridge Drain Pipe System Specifications | |
Fitting drawings | |
FRP Bridge Drain Pipe History | |
Enhanced Service Life | |
FRP BDP for Elevated Highways and Bridges |